NEW ORIGINAL WINTEK WM-CM 16X2 LCD MODULE SAME DAY SHIPPING! BOX#45 | Business & Industrial, Electrical Equipment & Supplies, Electronic. WM-CM FEATURE: I. 5 x 7 Dots with Cursor Item Supply Voltage for LCD Supply Current Sym. VDD- VO IDD 16×2 CHARACTERS ELECTRICAL. Full text of “Wintek Specfor LCD Module WM-CM-1YL Yc” . x x 1/16 30 o o o o o o o o 16×2 WD-CM x xlO.
|Published (Last):||6 February 2013|
|PDF File Size:||8.90 Mb|
|ePub File Size:||14.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
Can some one contribute to this wmc-1602m. I thank you for the help. LCDs are also very susceptible to changes in temperature, especially to prolonged exposure to high temperatures found in direct sunlight.
Such prolonged exposures to high temperatures can also permanently degrade various components of the LCD screen. My advice would be to replace the LCD screen, it appears to be a standard 16×2 HD compatible, and utilize a reflective cover which can be flipped up for viewing, this would ldd minimize the direct exposure ,cd sunlight and may reduce the devices temperature. It looks like this: I did already buy another display, but physically it does not match i found out after buyingthe first pin to soler is on a different distance from the edge, it lvd like this: It looks like cleaning the elastomers is working it is the causebut till now not completely resolving this isssue.
You need some small amount ld solder, soldering iron, solder wick and a solder sucker, none of which are too terribly expensive. There are numerous how-to videos available online which demonstrate desoldering techniques.
As far as locating a replacement, you’ll need to take some key measurements of the original unit and refer to the datasheet of a potential replacement unit before purchasing. You can also locate the datasheet of the original unit and obtain the dimensions and pin out from it.
The original LCD may have been degraded by prolonged exposures to high temperatures as the cover may have filter much of the harmful rays UV. The downside is the IR components of the sunlight were probably not filtered and the temperature of the LCD may have reached high levels during operation.
You might want to limit the devices operation to early mornings or late afternoons to minimize the operating temperature. The new display solder points, are 3 mm more to the left, starting from the edge see picture previous post.
So, perhaps i can bow the existing header pins 3mm, after removing the wwm-c1602m black horizontal bridge just below the pcb display. Does anybody have some experience with this, can it be done this bowing.
But, as told before, I wn-c1602m not have any experience on this, it is just how it looks like to me without any experience. Similar Threads Dewoo lcd lm32l1cd picture fading 2.
Connecting a A LCD display and a light sensor to Arduino UNO • Dreamdealer
Part and Inventory Search. AF modulator in Transmitter what is the A? Losses in inductor of a boost converter 8. Choosing IC with EN signal 1. Measuring air gap of a magnetic core for home-wound inductors and wm-c1602j transformer 7.
Hierarchical block is unconnected 3. Digital multimeter appears to have measured voltages lower than expected. PV charger battery circuit 4.
display (16*2) is fading, wintek lcd WM-CM-1GNNB
How reliable is it? Equating complex number interms of the other 6. CMOS Technology file 1. ModelSim – How to force a struct type written in SystemVerilog? Input port and input output port declaration in top module 2.
PNP transistor not working 2. Distorted Sine output from Transformer 8.
Analog Layout Finger Size 4. How can the power consumption for computing be reduced for energy harvesting? Dec 242: How do you get an MCU design to market quickly? Dec 248: Heat sinks, Part 2: Synthesized tuning, Part 2: The time now is